SKILSAW Table Saw Accessories: Real Upgrades for the TS6307-00

“SKILSAW table saw” almost always means one specific saw: the SKIL TS6307-00, a 15-Amp, 10-inch jobsite table saw with an integrated folding stand and a 25-1/2-inch rip capacity. SKILSAW itself is Chervon’s professional circular-saw sub-brand and barely touches table saws, so the accessories that actually fit are sold under the consumer-facing SKIL name — a mix-up that sends a lot of buyers searching the wrong part numbers. This guide covers the real accessories for the TS6307-00: the OEM zero-clearance and dado insert plates most listicles never mention, blade upgrades that fit its 5/8-inch arbor, dust collection, and the safety gear worth adding to the stock setup.

Blades: What Fits the TS6307-00’s 5/8-Inch Arbor

Every blade that fits the TS6307-00 has to match two numbers: a 10-inch diameter and a 5/8-inch arbor hole. Beyond that, tooth count decides what the blade is good at. A 24-tooth blade (what the saw ships with) clears material fast on rip cuts but leaves a rougher edge. A 40-tooth combination blade, like the Diablo D1040X above, is the practical middle ground most owners reach for once they start cutting plywood or trim instead of just framing lumber. An 80-tooth blade is worth adding only if you’re regularly cutting melamine or veneered panels where tear-out actually shows.

Skip any blade listed for a 5/8-inch bore but marketed for a different saw category (some framing and miter-saw blades share the bore size but not the plate thickness); check the listing’s stated arbor size against 5/8″ before buying; a blade with the wrong arbor either won’t seat on the shaft or will spin with dangerous wobble.

The Zero-Clearance and Dado Insert Plates Most Guides Skip

This is the accessory gap that generic “table saw accessories” listicles almost never mention by name: SKIL sells a model-specific zero-clearance insert plate (STZ6307) for the TS6307-00, which closes the gap around the blade in the stock throat plate and all but eliminates splintering on the underside of a cut — especially noticeable on plywood and veneered edges. There’s also a matching dado insert plate (STA6307) for owners who want to cut dadoes and rabbets on this saw.

The dado insert matters more than it sounds: the TS6307-00 accepts an 8-inch dado blade set, but the arbor washers that ship with the saw are sized for a single blade, not a stacked dado set. You have to rearrange or swap the washers per the dado set’s own instructions before first use — drop a stacked set on without doing that and it won’t sit flush or spin true. This step, not the dado set itself, is the most common reason a “compatible” dado stack feels wrong on a jobsite saw like this one.

Rip Fence and Miter Gauge: Where the Accuracy Actually Comes From

The TS6307-00 comes stock with a rack-and-pinion rip fence, which is the main reason it holds its adjustment better than the cheaper friction-lock fences on some competing jobsite saws — rack-and-pinion means turning the front knob moves the fence along a geared rail instead of just clamping it wherever you stopped pushing it, so it’s far less prone to drifting out of parallel mid-cut. If the stock fence has developed play, a replacement rip fence assembly is sold as an individual OEM part rather than requiring a whole new saw.

The included miter gauge handles crosscuts and angled cuts and is a standard-width bar that fits the saw’s miter slot. If you’re doing repeated identical crosscuts — picture-frame miters, box joints, batches of the same part — an aftermarket miter gauge with a flip-stop and micro-adjustable angle stops holds tolerances tighter than the stock gauge; for occasional angled cuts, the stock gauge is accurate enough on its own.

The Folding Stand: What It’s Built For, and What It Isn’t

The integrated folding stand is one of the TS6307-00’s main selling points over a benchtop-only saw — it folds flat for transport and unfolds to full working height without a separate stand purchase, which is why this saw shows up on jobsites as often as it does in home shops. What it isn’t built for is permanent, stationary use: the legs are tuned for portability, not for the rock-solid footing of a cabinet saw’s welded base, so on an uneven garage floor it’s worth shimming or leveling the feet rather than assuming the fold-out legs will self-level.

If you’re using the saw in one spot most of the time and only occasionally need to move it, a dedicated rolling stand with locking casters can be a more convenient upgrade than folding and unfolding the built-in legs every session — though it adds a separate piece of equipment to store, which defeats part of the reason people buy this saw in the first place.

Dust Collection: The Port Is There, But It Needs an Adapter

The TS6307-00 has a built-in dust port elbow at the rear of the saw, but like most jobsite saws in this class, it doesn’t include a shop-vac hose or a dust bag — you’re expected to supply your own. A standard 2-1/2-inch shop-vac hose with a hose-clamp fitting connects directly to the port; a dedicated dust collection bag is a lower-cost option if you don’t already own a shop vac, though it captures noticeably less fine dust than a real vacuum connection.

Fine sawdust from a table saw is a real respiratory irritant over repeated exposure, not just a mess — if you’re running this saw indoors regularly, pairing the dust port with an actual shop vacuum (not just the port on its own) makes a bigger difference to air quality than any other single accessory on this list. For a deeper look at cutting airborne dust further, see our guide on improving table saw dust collection.

Safety Accessories: What’s Built In vs. What You Should Add

The TS6307-00 ships with a blade guard, a riving knife, and an anti-kickback pawl already installed, plus a push stick in the box — more stock safety gear than some jobsite saws include. The riving knife rises and falls with the blade and keeps the kerf from pinching shut behind the cut, which is the main mechanism that causes kickback in the first place; leave it installed for standard cuts and only remove it for the specific non-through cuts (like some dado work) where the manual calls for it.

The one common gap is featherboards. Nothing in the box holds stock firmly against the fence through a long rip cut, and that’s exactly the situation where a hand creeping too close to the blade becomes a real risk. A magnetic featherboard clamps to the saw’s steel table without needing miter-slot mounting holes, and a shop-built featherboard does the same job for less money if you’d rather build one than buy it.

Checking Compatibility Before You Buy

Confirm the exact model number — TS6307-00 — before ordering any part beyond a generic 10″/5/8″ blade. SKIL’s own catalog covers several different table saws, and a fence, insert plate, or stand part built for one model isn’t guaranteed to bolt onto another. Blades are the one accessory category where cross-brand compatibility is genuinely common: any 10-inch blade with a 5/8-inch arbor, from Diablo, DeWalt, or elsewhere, will physically fit, even though SKIL-branded parts like the rip fence or the folding stand legs are saw-specific and won’t interchange with a Bosch, DeWalt, or Ryobi model. If you’re weighing this saw against those other brands, our Skil vs. Skilsaw brand breakdown explains why the “Skilsaw” name shows up on a SKIL-branded table saw in the first place.

Frequently Asked Questions

What accessories come with the SKILSAW TS6307-00?

The TS6307-00 ships with a 24-tooth blade, blade guard, riving knife, anti-kickback pawl, rip fence, miter gauge, push stick, two wrenches, a dust port elbow, and the integrated folding stand. It does not include a zero-clearance insert, dado insert, dado blade set, or a shop-vac hose — those are separate purchases.

Does the TS6307-00 have a zero-clearance insert available?

Yes. SKIL sells a model-specific zero-clearance insert plate (STZ6307) and a matching dado insert plate (STA6307) for the TS6307-00. The dado insert accepts an 8-inch dado blade set, but the stock arbor washers need to be rearranged per the dado set’s instructions before first use.

What size blade and arbor does the SKILSAW table saw use?

The TS6307-00 uses a 10-inch blade with a 5/8-inch arbor hole. Any blade matching those two dimensions fits, regardless of brand, as long as the plate thickness and hook angle suit the material being cut.

Can I use Bosch, DeWalt, or other brand accessories on a SKILSAW table saw?

Blades, yes, as long as the diameter and arbor size match. Fence assemblies, insert plates, and folding-stand parts are saw-specific and generally won’t fit across brands, or even across different SKIL table saw models — confirm the exact model number (TS6307-00) before ordering anything beyond a blade.

Conclusion

Most of what actually improves the TS6307-00 isn’t a mystery accessory — it’s the OEM zero-clearance insert (STZ6307) that most guides never mention by part number, a 40-tooth blade upgrade for cleaner crosscuts, a shop-vac hose on the dust port that doesn’t come in the box, and a featherboard to cover the one real safety gap in an otherwise well-equipped stock saw. Confirm the TS6307-00 model number before ordering anything beyond a 10-inch, 5/8-inch-arbor blade, and the rest of the stock saw holds up well.