How Much Does Curly Maple Lumber Cost Compared to Regular Maple?

How Much Does Curly Maple Lumber Cost Compared to Regular Maple?

Curly maple often costs roughly 1.5 to 3 times as much as plain maple, and highly figured boards can cost more when grain, color, and width line up. Paying that premium for a part that will be painted, hidden, or cut into narrow pieces wastes money fast. This guide compares the price gap, points to the main cost drivers, and shows when curly figure earns its place.

Maple price table

Maple price table
Pink maple leaves on a branch against a blurred blue background
Recommended gear
Budget pickBarrington Hardwoods Maple Lumber Boards 3/4" x 6" (3/4" x 6" x 48") (2pc)
Upgrade pickWoodpeckers Soft Maple Leg Stock Blank, S4S Kiln-Dried Hardwood, 3 x 3 x 36 in, 1-Piece, Furniture Legs & Turning, USA -
As an Amazon Associate we earn from qualifying purchases. Prices and availability are accurate as of the date shown and are subject to change.

The useful comparison is simple: curly maple is a figured maple product, while hard maple and soft maple are the regular benchmarks. Lumber is sold by the board foot, so the quoted price is the first number to compare before you look at thickness, surfacing, grade, and freight.

Stock and tier Curly maple price Regular maple price Dollar premium Premium percentage Buyer note
Less than 10 board feet, hard maple comparison $13.25/bf $6.00/bf $7.25/bf 120.8% Worth it for visible furniture parts where the curl should read after finish.
Less than 10 board feet, soft maple comparison $7.95/bf $6.00/bf $1.95/bf 32.5% Better when you want mild figure without moving far above regular maple cost.
4/4 stock, curly maple listing $6.60/bf $6.00/bf benchmark $0.60/bf 10.0% Small premium on this listing, but check surfacing, length, and grade before comparing.
5/4 bundle, 10 board feet $10.00/bf $6.00/bf benchmark $4.00/bf 66.7% Useful when you need thicker parts and want the figure on a show surface.
5/4 bundle, 100 board feet $10.00/bf $6.00/bf benchmark $4.00/bf 66.7% Buying more stock can improve consistency, but the figure premium remains sizable.

That table shows the buying split clearly. Curly maple does not carry one fixed markup. The premium shifts with species, figure intensity, thickness, and the supplier’s quantity tier. A buyer comparing a $13.25/bf curly hard maple board to a $6.00/bf hard maple board is paying far more than a buyer comparing curly soft maple to soft maple.

What you are paying for in the figure

Curly maple is maple with a wavy or curly grain pattern. The pattern often reads more strongly after finish is applied, so the same board can look modest in rough lumber and much more dramatic on a completed panel or door. That visible change is why the premium makes sense on exposed parts and wastes money on hidden ones.

Figure density and board selection

Boards with tighter, more even curl usually bring a higher price because the figure is more obvious and more consistent across a face. Suppliers also sort by appearance and yield. A board that looks good across a wide, clear face is more valuable than a shorter or narrower board with the same species name.

Why brown boards and sapwood matter

Curly maple may be sold as sap & better or as brown stock. Sapwood selection gives a lighter, cleaner look. Brown stock can be useful when you want a warmer tone, but it may not match as well across a set of parts. That selection affects both price and visual consistency.

Why is curly maple more expensive than hard maple or soft maple?

The premium comes from three sources: the figure itself, lower yield from sorting for attractive boards, and the fact that buyers pay more for a clear, selected face. Curly hard maple sits far above plain hard maple in the less-than-10-board-foot tier, while curly soft maple sits much closer to regular soft maple because the base species is cheaper.

Key points: Why is curly maple more expensive than hard maple or soft maple?

Yield loss from defects, width, and cut selection

Wide, clear, well-figured boards are harder to find than common maple stock. Knots, checks, color variation, and weak curl reduce usable yield. When a supplier trims out the less useful material, the price per board foot rises because you are paying for a smaller pool of better-looking lumber.

Why finish changes the value

Curly figure is easier to miss in raw lumber than in a finished piece. A clear finish or stain tends to make the chatoyance stand out. That is why curly maple is a strong buy for tabletops, cabinet doors, and drawer faces, but a weak buy for parts that will be painted or hidden behind hardware.

Say your project needs two 20-inch-wide cabinet doors and a matching 6-foot tabletop edge. Curly figure on the doors and top edge can carry the design, while plain maple on the rails, stiles, and internal stretchers keeps waste under control. The premium then pays for visible surfaces only.

Does thickness change the price?

Yes. Thicker stock usually costs more per board foot because it takes a larger log section to produce, and figured maple of greater thickness is harder to source in clean, usable form. Rough thickness also affects what you can actually use after surfacing. A common rule of thumb is that 4/4 board is about 1 inch rough, and 8/4 board is about 2 inches rough.

Quick steps: Does thickness change the price?

4/4, 5/4, 8/4, and 12/4 price differences

The Ocooch Hardwoods listing gives 4/4 curly maple at $6.60 per board foot, surfaced on two sides with rough edges, to 13/16 inch thick, and sold as forty-eight inches long or less. The same source lists 8/4 curly maple surfaced to 1 and 13/16 inch thick. The thicker stock costs more because you are buying more usable thickness and usually less common material.

For thicker figured stock, the premium can rise faster than the board-foot math alone suggests. A 9/4 board often costs more per board foot than 4/4 because the supplier has fewer thick, clean figured boards to sell. The log has to provide more depth, and the chance of defects increases as thickness rises.

How surfacing changes usable thickness

S2S means surfaced on two sides, planed smooth but not sanded. A common rule of thumb is that surfacing removes about 3/16 inch total, so the delivered thickness is less than the rough thickness. That matters when you are pricing a slab, because a board sold as 4/4 will not finish out to a full inch.

  1. Check the rough thickness first.
  2. Check whether the board is rough, S2S, or surfaced to final thickness.
  3. Subtract surfacing loss from your target dimension.
  4. Compare the usable thickness, not only the sticker price.

Grade and surfacing terms

Grade tells you more than appearance. Select and Better is the highest grade available on the cited curly maple listing, which signals mostly clear stock. Lower grades allow more character and more defects, so the price often falls, but the yield and appearance change with it.

Select & Better versus common grades

Select & Better is the common high-grade choice when the goal is clean, matched visible parts. Hard maple is also often sold as Select & Better or No. 1 Common. For curly maple, the grade matters because figure alone does not guarantee a useful board. You still need enough clear width and length for the part.

Rough stock versus S2S stock

Rough stock arrives unsurfaced and gives you full control over thickness reduction. S2S stock saves planing time and gives you a flat reference face, but it also removes thickness before you start milling. If you need a final 3/4-inch part, a surfaced board may not leave enough room for cleanup.

What to check in a supplier listing

Look for the species, thickness, grade, surface condition, length limits, and whether the stock is brown or sap & better. Also check whether freight or custom cutting is listed separately. Those charges are not part of the board-foot sticker price, and they can change the real cost of a small order.

When is curly maple worth the premium?

Curly maple is worth the extra cost when the grain will stay visible and part of the design. It is usually a poor buy for painted work, hidden cabinet interiors, and narrow parts that will be ripped down from wide stock. In those cases, regular maple gives the same structure for less money.

Furniture parts that benefit from figure

Tabletops, drawer fronts, aprons, shelves, and display panels are the best places to pay for curly maple. These are the parts most likely to catch light across the grain. If the board will be seen at arm’s length, the figure has a better chance of justifying the added cost.

Suppose a small dresser needs four visible drawer fronts and two side panels. Curly maple on those faces can carry the entire project visually, while standard maple inside the case keeps the budget in line. That split often gives better value than buying figured stock for every piece.

Cabinet doors, panels, and face frames

For cabinets, curly maple works best on doors, end panels, and open shelving where the face is visible. Face frames are a mixed case: if they are broad and exposed, the figure can matter; if they will disappear under hardware or trim, plain maple is usually the better purchase.

When regular maple is the better buy

Choose regular maple for paint-grade cabinets, interior parts, shop fixtures, drawer sides, backs, and hidden rails. Also choose it when you need a lot of pieces and the curl would be cut into narrow strips. The premium is easy to lose in waste when the figure is split across many small parts.

Choose curly maple if… / Choose regular maple if…

Use curly maple when the grain will be seen, the finish will be clear or lightly toned, and the board width will stay wide enough to show the figure. Use regular maple when the part is hidden, painted, or likely to be cut into narrow strips that waste the curl and raise cost per finished part.

  • Choose curly maple if: the part is a tabletop, door, panel, or other visible face.
  • Choose curly maple if: you want the grain to be part of the design after finish is applied.
  • Choose regular maple if: the part will be painted, enclosed, or covered by hardware.
  • Choose regular maple if: you need the lowest usable cost for internal cabinet parts or long runs of trim.

Keep reading

Frequently asked questions

How much more does curly maple cost than regular maple per board foot?

At the quoted less-than-10-board-foot tier, curly hard maple is $13.25/bf versus $6.00/bf for hard maple, a $7.25 premium or 120.8%. Curly soft maple is $7.95/bf versus $6.00/bf for soft maple, a $1.95 premium or 32.5%. The exact gap depends on figure, grade, and thickness.

What grades of curly maple are sold by lumber suppliers?

Suppliers commonly list curly maple as Select & Better, and some also sort it by sap & better or brown stock. Select & Better usually signals mostly clear lumber. Sapwood selection affects both appearance and consistency, while brown stock can change the color match across a project.

Is curly maple usually sold rough, S2S, or project-ready?

It is often sold rough or S2S, not fully project-ready. The cited listing describes 4/4 curly maple as surfaced on two sides with rough edges, and it is sold in a specified rough thickness. Buyers should check whether the board is rough, S2S, or surfaced to final thickness before planning cuts.

What board-foot price should I expect for hard maple versus curly maple?

A common benchmark in the quoted pricing is $6.00/bf for hard maple and $13.25/bf for curly hard maple in the under-10-board-foot tier. That puts curly hard maple at a little over twice the plain hard maple price. Soft maple remains the lower-cost comparator at $6.00/bf in the same tier.

Are there cheaper figured maple options besides curly maple?

Yes. Birdseye maple in the cited pricing is $13.50/bf, and quilted Western Maple is $40.00/bf for less than 10 board feet. Curly soft maple at $7.95/bf is one lower-cost figured option, and it may be the better choice if you want some figure without paying curly hard maple prices.

Why does 9/4 curly maple cost more per bf than 4/4?

Thicker figured stock is harder to source and more likely to lose usable area to defects or surfacing. A 4/4 board starts near 1 inch rough and the cited listing surfaces it to 13/16 inch, while thicker stock must come from larger, cleaner log sections. That scarcity drives the higher per-board-foot cost.

Similar Posts